异型钢单缝式伸缩装置

服务	橱柜	详细地址	路北-橡塑路
QQ号	1334576766

异型钢单缝式伸缩装置

GQFC型、GQFZ型、GQFL型、GQFF型、GQFMZL型模数式桥梁伸缩装置，是采用热轧整体成型的异型钢材设计的桥梁伸缩装置。GQFC型、GQFZ型、GQFF型、GQFL型伸缩装置适用于伸缩量80mm以下的桥梁接缝，GQFMZL型伸缩装置是由边梁、中梁、横梁和连动机构组成的模数式桥梁伸缩装置，适用于伸缩量80mm-1200mm的大中跨度桥梁。

GQF C type， GQF Z type， GQF L type， GQF F type and GQF MZL modulus bridge expansion device are bridge expansion devices designed by hot rolled integral shaped steel products. GQF - C bridge joint type， GQF - Z， GQF - F， GQF - L telescopic device is suitable for the expansion amount below 80mm， GQF - MZL type expansion device is a modular bridge expansion device is composed of edge beam， beam， beam and linkage mechanism， suitable for large and medium expansion 80mm-1200mm long span bridge.

2、设计制造技术条件

2. Technical conditions for design and manufacture

1、设计荷载：采用J刊公路工程技术标准规定的汽车超过20级荷载进行设计。

1， design load using J magazine 01 - highway engineering technical standard stipulated in the vehicle over 20 load to carry out the design.

2、本结构使用的异型钢材质为16Mn桥梁专用钢，钢材抗拉强度应不低于480Mpa，容许弯曲应力不低于210Mpa。

2. The special-shaped steel material used in this structure is 16Mn bridge special steel. The tensile strength of steel should not be less than 480Mpa， and the ading stress is not less than 210Mpa.

3、结构中支承横梁使用16Mn或45号钢，其容许弯曲应力不低于210Mpa。

3. 16Mn or No. 45 steel is used in the supporting beam in the structure， and the ading stress is not less than 210Mpa.

4、其余配件钢材可使用不低于Q235强度钢材。

4， the rest of the fittings steel can be used not less than Q235 strength steel.

3、胶料适用范围

3. The scope of application of rubber

1、采用氯丁橡胶（C日）的伸缩装置适用于温度为25+60地区。

1. The telescopic device used for chloroprene rubber （C day） is suitable for the temperature range of - 25 - C - +60 C.

2、采用天然橡胶（N日）的伸缩装置适用于温度为40+60地区。

2. The expansion device of natural rubber （N day） is suitable for the temperature range of - 40 C to +60 C.

异型钢单缝式伸缩装置

A single slit expansion device for special-shaped steel

异型钢单缝式伸缩装置由一条整长的橡胶密封条，一组钢质边梁及锚固件组成。钢质边梁内侧带 有能固定橡胶密封条的沟漕。焊固在钢梁外侧的锚固件，与梁端预埋钢筋相焊接，浇筑高强度混凝土过渡段后，同志梁体连接可靠，具有与桥面接合平顺，密封止 水，伸缩灵活，行车平稳，使用寿命长的特点。适用于伸缩量0-80mm的桥梁。

The special-shaped steel single slit expansion device consists of a whole long rubber seal， a group of steel side beams and anchors. The inside of the steel side beam has a ditch that can be fixed with a rubber seal. The anchorage piece fixed on the outer side of the steel beam is welded with the embedded steel bar at the beam end. After pouring the transition section of the high strength concrete， the connection of the comrade beam body is reliable， and has the characteristics of smooth connection with the bridge deck， sealing and water stopping， flexible expansion， stable driving and long service life. The bridge is suitable for the expansion of 0-80mm.

异型钢单缝式伸缩装置伸缩量的确定

Determination of expansion capacity of single slit expansion device for special-shaped steel

桥梁伸缩量计算值直接影响对伸缩缝规格选定，若伸缩缝规格选择不合理， 就直接影响伸伸缩缝的使用效果，同时选择伸缩装置时还应考虑梁、 板间伸缩装 置间隙量大小，以保证伸缩缝装置与梁、板两端有充分锚固，才能达到佳使用效果。所以在选择伸缩缝的规格时，一定要留充足余量，才能保证伸缩缝的使用 效果和耐久性.1

The value of a direct impact on the expansion joint specifications selection calculation of bridge expansion joints， if the specifications are not reasonable， directly affects the use effect of stretch contraction joints， and telescopic device should be taken into consideration when the beam and plate expansion device gap size， to ensure that the expansion joint device and beam， plate ends have sufficient anchorage， can to achieve the best results. So when choosing the size of the expansion joint， we must leave sufficient allowance to ensure the use effect and durability of the expansion joint.1.